Industrial Maintenance
Preventive and corrective maintenance, electronic board repair, hydraulic and pneumatic systems, spare parts and upgrades for industrial equipment in Monterrey and across Mexico.
Does any of this sound familiar?
What we do, how it works and what results to expect
Each service addresses a specific problem in your operation. Choose the one closest to your case and talk directly with a specialist.
Preventive and corrective maintenance of industrial equipment
We provide preventive and corrective maintenance for industrial, rotating and process equipment, both electrical and mechanical.
It's for you ifyou have equipment that is down or failing, or your preventive maintenance follows a calendar and you still have unplanned downtime.
- Diagnosis with the real cause of the failure
- A maintenance program tailored to your plant
- Work performed during the agreed shutdown window
What you get and how it works
What you get: The equipment back in operation and a report with what was found, what was corrected and what should be addressed next.
How it works: We inspect the equipment, diagnose the cause, source the spare parts and carry out the work. If needed, we build a tailored maintenance program with you.
Electrical diagnostics of motors and equipment
We measure the equipment supply on site while it runs: voltage, current, phase imbalance and harmonics.
It's for you ifyou have a motor that overheats or trips, a drive with repeated faults, or you want to check equipment before accepting it.
- The electrical cause of the failure, backed by measured data
- Assessment with the equipment running
- Specific corrective recommendations
What you get and how it works
What you get: A report with the measurements, what we found and what should be corrected.
How it works: We connect the analyzer at the equipment panel or starter, record its behavior during normal operation and compare the values against nameplate data and the applicable limits.
Repair of electronic boards and equipment
We perform component-level repair of electronic boards, variable frequency drives, power supplies, control modules and operator interfaces for industrial equipment.
It's for you ifnew equipment takes weeks to arrive, it has been discontinued, or you need your line running again while you decide on a replacement.
- Component-level diagnosis
- Equipment tested before delivery
- An alternative when the equipment is no longer manufactured
What you get and how it works
What you get: The board or equipment repaired and tested, with a report of the fault found.
How it works: We receive the equipment, diagnose it and confirm the scope before repairing it. We deliver it tested and ready to install.
Hydraulic, pneumatic and lubrication systems
Maintenance, repair and spare parts for hydraulic, pneumatic and lubrication systems: power units, pumps, valves, cylinders, hoses and centralized lubrication.
It's for you ifyour system loses pressure, leaks, overheats or no longer responds as it used to.
- Advice from specialists with industry experience
- Spare parts and maintenance from a single supplier
- Pressure, performance and reliability restored
What you get and how it works
What you get: The system inspected and corrected, with a report of the work performed and the parts replaced.
How it works: We inspect the system on site, identify the cause, source the spare parts and carry out the correction.
Specialized spare parts sourcing
We source the spare part or consumable your industrial equipment needs, even if it is hard to find or discontinued. If it no longer exists, we propose a working equivalent.
It's for you ifyou have equipment down waiting for a part, or your supplier no longer carries it.
- Search for hard-to-find or discontinued parts
- Technically validated equivalents
- A single contact for multiple brands
What you get and how it works
What you get: The spare part or proposed equivalent, with the technical information to validate it.
How it works: Share the nameplate, part number or a photo with us. We locate the part or its equivalent and confirm the delivery time.
Equipment commissioning and upgrades (retrofits)
We install, start up and upgrade industrial equipment: replacement of obsolete controls, motors and components, with support rigging when needed. We hand it over tested and running.
It's for you ifyou are going to install new or relocated equipment, or yours works but has obsolete components with no spare parts.
- Installation and start-up with a single point of responsibility
- Current components with available spare parts
- Equipment handed over tested and running
What you get and how it works
What you get: The equipment installed or upgraded, tested and running, with the job documentation.
How it works: We define the scope with you, prepare the engineering and carry out the installation or upgrade during the agreed shutdown window.
Predictive Monitoring Program
We interpret the real condition of your critical equipment and define the right intervention while there is still time to choose when to do it.
It's for you ifyou want to stop finding out about failures after the equipment has already stopped.
How the direct line works
- The equipment changes its behaviorVibration, temperature or current outside its normal pattern.
- We detect and analyze itA specialist confirms the condition and the probable cause.
- We alert you with what is happeningWe explain what is going on and when it is best to intervene.
- We schedule the interventionIn the window you choose, with the spare part already identified.
Not sure which one you need?
Tell us which equipment is giving you trouble and we will tell you which service fits.
One team from start to finish
Whether it is maintenance, a study, a repair or an upgrade, the same team handles the survey, the engineering, the execution and the commissioning. You decide the scope at every stage.
Site survey
We visit your plant, review the installation and understand the real need.
Engineering and proposal
We diagnose the cause and define the solution: scope, timing and cost.
Execution
We repair, maintain, install or upgrade with our own team.
Testing and commissioning
We test on site and start up with you; nothing is handed over without verification.
Handover and follow-up
We document the work and follow up so the result lasts.
↻ Something new comes up? The same team returns to the site survey
One point of responsibility from start to finish
No intermediaries or separate suppliers to coordinate: the same team is accountable for the result.
What people ask us most
What types of equipment do you service?
Industrial equipment in its electrical, electronic, mechanical, hydraulic and pneumatic parts: motors, pumps, compressors, gearboxes, variable frequency drives, electronic boards and lubrication systems, among others.
Do you handle urgent failures?
Yes. Message us on WhatsApp with a description and photos of the failure; we respond within 24 business hours.
Where do you provide service?
We are based in Monterrey, Nuevo León, and serve plants throughout Mexico.
Can you repair a board or equipment that is no longer manufactured?
In many cases, yes. We diagnose it at component level and, if repair is not viable, we propose an equivalent.
What information do you need to quote?
The brand, model and nameplate data of the equipment, photos, a description of the failure or job, and the plant location.
What is the Predictive Monitoring Program?
It is our service for critical equipment: we interpret its real condition using the data your plant already generates and alert you when it is best to intervene, before a failure stops production.
Our other divisions
Facing any of these problems in your operation?
Tell us about your situation and we will help you define the first step. No obligation.